AIThis post was created with the assistance of artificial intelligence (AI).

TL;DR

A GreenBuildingAdvisor report says radiant cooling can be practical in humid climates, but it cannot replace dehumidification. The system must keep its cooling surfaces above the indoor air’s dew point, which limits cooling capacity; the report says this can suit efficient new homes better than older, less efficient ones.

Radiant cooling can work in humid climates, but a GreenBuildingAdvisor report says it requires a separate way to remove moisture and controls that keep cooled surfaces above the air’s dew point. Those conditions can make the approach suitable for some efficient homes, while limiting its usefulness in buildings with larger cooling loads.

Before you orderOffer from Amazon

Get backup power and energy gear delivered free with Prime

  • Fast, free delivery on millions of items
  • Prime Video, Amazon Music and more included
  • Member-only deals all year
Start your free Prime trial Free trial for eligible customers · Cancel anytime
As an affiliate, we earn on qualifying purchases.

Radiant systems cool rooms through panels or building surfaces, commonly using water circulated through tubes. People exchange heat with their surroundings through radiation, so cooler surfaces can improve comfort even when the air itself is not as cold as it might be with conventional air conditioning. The report also points to a practical advantage: hydronic tubing takes less space than ductwork. Its author describes indoor-air-quality benefits as possible, not guaranteed, because well-filtered air-conditioning systems can also keep coils and drain pans clean.

The central concern in a humid climate is condensation. When a surface becomes colder than the dew point of the surrounding air, moisture can form on it. The report gives an example of indoor air at 75°F and 65% relative humidity, with a dew point of about 62°F. It says radiant-cooling professionals commonly recommend keeping surfaces at 65°F or warmer under humid conditions, leaving a temperature difference of about 10°F from the room air.

Radiant panels address the home’s sensible cooling load—reducing temperature—but do not, by themselves, remove water vapor. The report says a home in a humid climate needs a dehumidifier or another source of moisture control; relying on radiant cooling alone can lead to high indoor humidity and condensation. It estimates capacity at 15,000 to 25,000 BTU per hour per 1,000 square feet of panel area, and argues that this can meet the needs of a well-built new home. It cautions that older, less efficient homes may require more cooling than the system can provide within safe surface-temperature limits.

At a glance
reportWhen: Published date not provided; the report…
The developmentA GreenBuildingAdvisor report outlines the humidity-control and capacity limits that determine whether radiant cooling is practical in humid climates.

Humidity Control Sets the Limits

The report’s main practical point is that radiant cooling in a humid region is not simply a swap for a conventional air conditioner. Homeowners and designers have to plan for temperature control and moisture removal as separate tasks. If humidity control fails, cooling surfaces may collect condensation; if surfaces are kept warmer to avoid that risk, the system’s available cooling output is constrained.

That distinction affects both system design and expectations. A radiant system may offer comfort and avoid extensive ductwork, but its feasibility depends on the home’s heat load, panel area, and the performance of its dehumidification equipment. The report’s capacity range is a general estimate, not a guarantee for a particular building. A project needs a load calculation and a humidity-control plan rather than a decision based on the technology alone.

Products Worth Considering

Ring Alarm 8-Piece Kit (Newest Model) – Home Security System

Ring Alarm 8-Piece Kit (Newest Model) – Home Security System

Sony BRAVIA XR8B 65-Inch OLED 4K HDR Smart Google TV (K-65XR8B)

Sony BRAVIA XR8B 65-Inch OLED 4K HDR Smart Google TV (K-65XR8B)

As an affiliate, we earn on qualifying purchases.

How Dew Point Shapes Design

Radiant cooling works by transferring heat between people and cooler surrounding surfaces. The GreenBuildingAdvisor report notes that roughly 60% of heat exchange between a person and the surrounding environment occurs through radiation. This helps explain why surface temperatures can affect comfort even when air temperature is unchanged. The report also points to radiant heating and cooling panels installed in the hallway of ASHRAE’s Atlanta-area headquarters, photographed at a 2021 ribbon-cutting ceremony, as an example of the technology in use.

The comparison with dry climates is important: dry outdoor conditions generally make moisture control less demanding. In humid climates, air conditioning itself may not keep indoor relative humidity low enough at all times. The report says mid-60% humidity readings can occur in air-conditioned homes in the Atlanta area, particularly during difficult weather. Radiant systems therefore need active humidity management and safeguards tied to indoor dew point, not just a target room temperature.

““The dew-point temperature of the indoor air is of paramount importance, especially with radiant cooling.””

— GreenBuildingAdvisor report

Performance Depends on Each Home

The report’s estimates do not establish that radiant cooling will meet the needs of every home. Actual performance depends on local humidity, indoor dew point, panel area, and the building’s cooling load. The supplied report excerpt does not provide a full design method, equipment specifications, installation costs, or measured operating results for a particular residence. It also does not quantify how much electricity a combined radiant-cooling and dehumidification system would use compared with conventional air conditioning.

It remains unclear from the material provided how the system’s controls should respond to fast changes in humidity or what specific backup measures a given installation should use. The report’s Atlanta example and capacity range offer context, but they are not a substitute for project-specific engineering.

What a Homeowner Should Check

Anyone considering radiant cooling in a humid region should first have the home’s cooling load and moisture-control needs assessed. A designer can determine whether the available panel area can meet the sensible load while keeping surfaces above the expected dew point, and specify a separate dehumidification system. Controls should account for indoor humidity as well as temperature so the system can reduce cooling or respond if condensation risk rises.

The next step is a comparison of the full system—not just the radiant panels—with alternatives, including installation requirements, operating costs, and comfort goals. The report does not announce a new product or policy milestone; its conclusion is conditional: radiant cooling may make sense in humid climates when moisture is controlled and the building’s load is compatible with the system’s capacity.

Key Questions

Can radiant cooling work in a humid climate?

Yes, according to the GreenBuildingAdvisor report, but it requires separate humidity control and safeguards against condensation on cooled surfaces.

Why can radiant cooling cause condensation?

If a panel or floor is colder than the dew point of the surrounding air, moisture can collect on that surface. The report’s example puts the dew point near 62°F when indoor air is 75°F at 65% relative humidity.

Does radiant cooling remove humidity?

Not by itself. Radiant panels handle sensible cooling, or lowering temperature; the report says a humid-climate home also needs a dehumidifier or another moisture-control method.

How much cooling capacity does the report estimate?

It gives a range of 15,000 to 25,000 BTU per hour per 1,000 square feet of panel area. That is a general estimate, not a performance promise for an individual home.

Is radiant cooling a good fit for an older home?

It may be harder to apply where the cooling load is high. The report says efficient new homes may be a better fit and cautions that older, less efficient homes can need more capacity than radiant panels can provide while remaining above the dew point.

Source: rss

You May Also Like

Fraunhofer ISE achieves 34.4 efficiency for III-V germanium solar module

Fraunhofer ISE achieves 34.4% efficiency in a III-V germanium solar module using shingle-matrix technology and space-grade cells, surpassing previous records.

Solar Industry Spends To Flip Control Of Georgia Utility Commission

A solar industry group is spending $250,000 to support two Democrats seeking seats on Georgia’s Public Service Commission.

More Heat Pumps Would Actually Be Good For The Grid, Researchers Find

An RMI study estimates more heat pumps could spread fixed grid costs and lower residential electricity rates in 24 states and Washington, D.C.

Actelis Networks Surges In Global Coverage

Actelis Networks experiences a surge in worldwide coverage, with 19 media mentions in the recent window, indicating increased industry and public interest.